Your disposal hums but won't spin โ the impeller plate is jammed. It's completely silent when you flip the switch โ the thermal overload protector has tripped or the motor has failed. Water drips from the sink collar โ the sink mounting gasket has deteriorated. Each of these is a different diagnosis, and each has a different solution. Masters Plumbing Service's techs in Delafield, WI arrive with the jamming tools, reset wrench, and replacement units to resolve any disposal failure same visit.
๐ Call +1-855-718-1500 โ Same-Day Service
We carry replacement units on the truck in common horsepower ratings so a same-day swap is possible when the motor has genuinely failed.
A disposal that hums but won't spin almost always just needs the jam cleared with an Allen wrench at the center socket and the reset button pressed โ a 5-minute fix that doesn't require a new unit.
InSinkErator (Badger, Badger 5, Compact, Evolution series), Moen GXS/GX series, Waste King, KitchenAid, and Whirlpool disposals all mount differently and have specific jam-clearing procedures. We know the mounting assembly for each brand and carry the correct jam-clearing wrench sizes.
We give you the actual cost comparison. If clearing the jam and pressing the reset button fixes it, that's what we do. If the motor has failed, we show you the replacement options and install same-day.
A disposal isn't an isolated appliance โ it connects to the sink drain, the dishwasher drain (if present), and the drain arm leading to the p-trap. We inspect the full connection set during any disposal call: drain arm slope, dishwasher drain knockout (if a dishwasher is being added), and p-trap connection integrity.
From a simple jam clear to a full replacement with drain reconnection, here's how we handle each garbage disposal scenario in Delafield, WI.
If the jam-clearing wrench won't budge the impeller, the motor shaft may be seized rather than just stuck from debris โ we distinguish between the two before recommending replacement.
If power is confirmed at the disposal and it still won't start after a reset, the motor is failed. We then move to the replacement conversation with honest cost comparison.
Disposal leaks come from three locations: the sink flange (top of the unit where it mounts to the sink drain opening โ repaired by re-sealing the flange with plumber's putty and re-tightening the mounting ring), the side port (dishwasher drain hose connection โ usually a loose hose clamp or cracked fitting), or the bottom of the unit (internal body crack or failed internal seal โ indicates replacement needed).
An unusually loud grinding, rattling, or metal-on-metal sound from a disposal almost always means either a hard object (bottle cap, small utensil, pit from stone fruit) is in the grinding chamber, or an impeller piece has broken and is contacting the shredder ring. We access the grinding chamber safely, remove any foreign objects, and inspect the impeller and shredder ring for damage.
If the slow drain persists after cleaning the drain arm and p-trap, a camera scope of the kitchen drain line is the next step to check for blockage further downstream.
When the motor has failed, the unit body is cracked, or the existing unit is underpowered for the household's use pattern, we replace the disposal with a new unit matched to the sink drain configuration. We carry 1/2 HP, 3/4 HP, and 1 HP units from InSinkErator and other major brands on our trucks for same-day installation.
No guesswork โ we diagnose before we quote, and quote before we start.
If you know the disposal is over 10 years old, tell us โ that changes how we approach the repair-vs-replace conversation upfront.
For leaks, we dry the area completely and run a short test cycle to confirm exactly which connection is dripping.
You decide. We don't upsell replacement when repair is the right answer, and we don't push a cheap repair that won't hold on a unit that's genuinely at end of life.
We leave the cabinet dry and the disposal running quietly. If a dishwasher drain hose was involved, we run a dishwasher cycle to verify no backup occurs.

The disposal under our kitchen sink was 12 years old and started leaking from the bottom โ which the tech explained is always an internal seal failure, not a repairable condition. He had a replacement 3/4 HP InSinkErator on his truck, installed it in about 45 minutes, and the kitchen is back to normal. Old unit got pulled, new unit tested clean, no leaks at any connection.
Disposal making a loud rattling noise but still grinding. Tech took out a bottle cap that had gotten past the splash guard and was spinning around the grinding chamber. Cleaned out the chamber, confirmed the impeller wasn't damaged, tested for smooth operation. Twenty-minute visit, everything working perfectly.
Disposal leaking from the sink collar area. Previous owner had installed it with silicone instead of plumber's putty at the flange โ silicone doesn't hold the mounting pressure correctly and had separated. Tech re-seated the flange with putty, re-tightened the mounting ring, and the leak stopped. Tested with a full minute of running water. All clear.

Masters Plumbing Service dispatches garbage disposal repair and replacement technicians throughout Delafield and the broader Delafield, WI service area. Most calls are same-day โ call to check today's availability.

Our disposal techs in Delafield, WI carry the tools and replacement units to resolve any disposal problem same visit. Flat-rate pricing, honest repair-vs-replace guidance, and no unnecessary upselling.
๐ Call +1-855-718-1500 Now